18 Best Wood Lathe Chucks

 

PSI Woodworking CSC3000CTN Barracuda 2 Special Edition TN 12 Piece Lathe Chuck System

PSI Woodworking CSC3000CTN Barracuda 2 Special Edition T/N, 12 Piece Lathe Chuck System

PSI Woodworking CSC3000CTN Barracuda 2 Special Edition T/N, 12 Piece Lathe Chuck System - Mounting holes can be held internally from 11/16-to-3-3/8-inch diameter. Round stock can be held externally from 3/32-to-4-3/8-inch diameter bowls can be held by the outside rim up to a 5-inch diameter. Suitable for mini, midi and full sized lathes. Features include an indexing accessory, a screw chuck, and a 5/8-inch super spur drive center insert. Direct drive gear tooth jaw tightening “t” handle allows one-hand operation.

 

Hurricane Turning Tools Step Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Step Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Step Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck - These jaws are used in expansion mode for internal holding within a straight wall. These jaws are only compatible with the htc125. Normally, these are used holding small items like a box or lid. This listing is for a set of step jaws with serrated grip , which are used on the hurricane htc125 4 jaw woodturning scroll chuck.

 

Hurricane Turning Tools JumboCole Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Jumbo/Cole Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Jumbo/Cole Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck - These jaws are only compatible with the htc100. . This listing is for a set of jumbo / cole jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. The jaw set comes with 8 buttons which can be placed in the various hole locations to accommodate a variety of bowl sizes. The buttons open to about 12 inches. These jaws are used for gripping the top of a bowl in compression or expansion mode, allowing you to finish the bottom of the bowl.

 

Hurricane Turning Tools Spigot Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Spigot Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Spigot Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck - The outside jaws are serrated. They are very useful for holding inside a candlestick. This listing is for a set of spigot jaws, which are used on the hurricane htc125 4 jaw woodturning scroll chuck. Spigot jaws can be used in expansion mode for internal holding within a straight wall. Normally, these are used holding small items like a box or lid. These jaws are only compatible with the htc125. In compression mode, they can be used for holding small work.

 

Hurricane Turning Tools Standard Dovetail Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Standard Dovetail Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Standard Dovetail Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck - They can also be used in expansion mode for holding inside a dovetail recess. Measurements compression 1 3/4″, 3″ expansion 2 1/4″, 3 1/2″. These jaws are normally included in the basic chuck kit, but you might need an extra set, or purchased a chuck as “body only” these jaws are only compatible with the htc100. Standard dovetail jaws are the most common jaw type used in woodturning. This listing is for a set of standard dovetail jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. They are typically used in compression mode for holding a tenon or “foot” on the bottom of a bowl or platter.

 

Hurricane Turning Tools Extended Dovetail Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Extended Dovetail Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Extended Dovetail Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck - You can also use them in compression mode to hold small object down to these jaws are only compatible with the htc125. This listing is for a set of extended dovetail jaws, sometimes called spindle nose jaws, which are used on the hurricane htc125 4 jaw woodturning scroll chuck. They are used in expansion mode for internal holding within a dovetail recess. This gives you better access to the bottom of the bowl for easier tool work while your bowl is on the lathe. The dovetail is set away from the flat jaw surface by about 1 inch.

 

PSI Woodworking CSC500K Barracuda Micro Key Lathe Chuck System

PSI Woodworking CSC500K Barracuda Micro Key Lathe Chuck System

PSI Woodworking CSC500K Barracuda Micro Key Lathe Chuck System - Weighs only 12 pounds with a 2-1/8-inch outside diameter. Mounts to 3/4-inch-by-16 tpi & also adapts to 1-inch-by-8 tpi. Includes step jaws, round jaws, and pin jaws. Holds workpiece from 5/8-to-2-inch inside hole diameter. Holds dowell from 1/4-inch up to 1-1/2-inch outside diameter.

 

PSI CSC2000C Barracuda Wood Lathe Chuck System

PSI CSC2000C Barracuda Wood Lathe Chuck System

PSI CSC2000C Barracuda Wood Lathe Chuck System - Includes #2 round jaws, for dowels1-1/2″ to 2-7/8″, holes 2″ to 3-1/2″. Includes four(4) self-centering jaw sets to hold round and square stock for turning, pre-threaded for 1″ x 8 tpi, and has an adapter for 3/4″ x 16 tpi spindles. Includes #1 step jaws- for dowels 1/32″ to 1-1/2″, holes 11/16″to 3-1/8″. Includes pin jaws which hold inside holes 1″, 2-1/2″, and a screw chuck. Includes #3 round jaws, external grip 3-1/16″, 4-1/2″.

 

Hurricane Turning Tools Standard Dovetail Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Standard Dovetail Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Standard Dovetail Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck - Measurements compression 2 1/4 “, 4 1/8″ expansion 2 7/8″, 4 3/4″. Standard dovetail jaws are the most common jaw type used in woodturning. This listing is for a set of standard dovetail jaws, which are used on the hurricane htc125 4 jaw woodturning scroll chuck. They are typically used in compression mode for holding a tenon or “foot” on the bottom of a bowl or platter. These jaws are normally included in the basic chuck kit, but you might need an extra set, or purchased a chuck as “body only” these jaws are only compatible with the htc125. They can also be used in expansion mode for holding inside a dovetail recess.

 

Hurricane Turning Tools Step Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Step Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Step Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck - . This listing is for a set of step jaws with serrated grip , which are used on the hurricane htc100 4 jaw woodturning scroll chuck. These jaws are only compatible with the htc100. These jaws are used in expansion mode for internal holding within a straight wall. Normally, these are used holding small items like a box or lid.

 

PSI CSC2000C Barracuda Wood Lathe Chuck System by PSI Woodworking

PSI CSC2000C Barracuda Wood Lathe Chuck System by PSI Woodworking

PSI CSC2000C Barracuda Wood Lathe Chuck System by PSI Woodworking - Screw chuck insert for bowl turning. Chuck body threaded 1-1/2-inch by 8tpi, with optional adapters to 1-inch by 8tpi, 1-1/4-inch by 8tpi, m33 by 35 mm. Comes with 4 sets of jaws 1 step jaws, 2 round jaws, 3 wide jaws and pin jaws. Psi csc2000c barracuda wood lathe chuck system. Long shaft chuck key, “t” handled allen wrench.

 

Hurricane Turning Tools Pin Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Pin Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Pin Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck - . These jaws are only compatible with the htc100. The straight side can be used to hold the inside of a small box body. In compression mode, they can grip a small part like a final, or pen mandrel. These jaws are for small work and have several uses used in expansion mode for internal holding within a dovetail recess. This gives you better access to the bottom of the bowl for easier tool work while your bowl is on the lathe. The dovetail is set away from the flat jaw surface by about 1 inch. This listing is for a set of pin jaws with dovetail , which are used on the hurricane htc100 4 jaw woodturning scroll chuck.

 

Hurricane Turning Tools Large Serrated Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Large Serrated Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Large Serrated Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck - They differ from dovetail jaws in that they are not tapered and have tiny gripping “serrations”. This listing is for a set of large serrated jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. Serrated jaws are used for gripping end grain cylinders. . Some turners use the serrated jaws instead of dovetail jaws in compression mode for gripping a tenon or expansion mode for internal holding within a recess. They can be used for this but they are not as strong as dovetail jaws.

 

PSI CMG3C Mini Grip 4 Jaw Wood Lathe Chuck System

PSI CMG3C Mini Grip 4 Jaw Wood Lathe Chuck System

PSI CMG3C Mini Grip 4 Jaw Wood Lathe Chuck System - Stepped jaws for small dowels 3/8-to-1-1/4-inch to grip internally 1-to-2-1/2-inch. Adapts to both 3/4-inch-by-16 tpi and 1-by-8 tpi spindles, and contains 2 open/close levers. Flat jaws to handle bowls up to 5-inch diameter are available (#cjawfj1). Basic straight jaws for 1-inch stock, square or round. Bonus jaws to hold dowels 1-1/2-to-2-3/8-inch to grip internally 2-to-3-inch.

 

Hurricane Turning Tools Pin Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Pin Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Pin Jaws for HTC125 Woodturning 4 Jaw Wood Lathe Chuck - This listing is for a set of pin jaws with dovetail , which are used on the hurricane htc125 4 jaw woodturning scroll chuck. These jaws are only compatible with the htc125. The straight side can be used to hold the inside of a small box body. This gives you better access to the bottom of the bowl for easier tool work while your bowl is on the lathe. The dovetail is set away from the flat jaw surface by about 1 inch. In compression mode, they can grip a small part like a final, or pen mandrel. These jaws are for small work and have several uses used in expansion mode for internal holding within a dovetail recess.

 

PSI Woodworking CSC3000C Barracuda Wood Lathe Key Chuck System

PSI Woodworking CSC3000C Barracuda Wood Lathe Key Chuck System

PSI Woodworking CSC3000C Barracuda Wood Lathe Key Chuck System - Includes pin jaws which hold inside holes 1-to-2-1/4-inch, and a screw chuck. Includes #1 step jaws for dowels 3/32-to-1-3/8-inch, holes 11/16-to-2-3/8-inch. Includes #3 round jaws, external grip 3-1/16-to-4-3/8-inch. Includes four (4) self-centering jaw sets to hold round and square stock for turning, pre-threaded for 1x8tpi, and has an adapter for 3/4x16tpi spindles. Includes #2 round jaws, for dowels 7/8-to-1-1/2-inch holes 1-1/4-to-2-inch.

 

Hurricane Turning Tools Spigot Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Spigot Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck

Hurricane Turning Tools, Spigot Jaws for HTC100 Woodturning 4 Jaw Wood Lathe Chuck - This listing is for a set of spigot jaws, which are used on the hurricane htc100 4 jaw woodturning scroll chuck. Normally, these are used holding small items like a box or lid. In compression mode, they can be used for holding small work. They are very useful for holding inside a candlestick. These jaws are only compatible with the htc100. Spigot jaws can be used in expansion mode for internal holding within a straight wall. The outside jaws are serrated.

 

Sherline 1043 - 3-Jaw Self-centering Wood Lathe Chuck

Sherline 1043 – 3-Jaw Self-centering Wood Lathe Chuck

Sherline 1043 – 3-Jaw Self-centering Wood Lathe Chuck - It has a clamping range of 3/32″ (2 mm) up to 1-3/16″ (30 mm) diameter with the jaws in the normal position. If you have sent in an old chuck for jaw replacement or are replacing an old, worn chuck, you will notice that the new one is initially harder to turn than your worn one. Grinding is done to within. 0001″. Because this chuck was initially designed for machine-lathe work, its accuracy far exceeds what is necessary for general wood turning. Sherline technicians custom grind each jaw to fit its own slot with as little play as possible. 687″ (17 mm). Tommy bars (provided) are used in the holes in the side to tighten and loosen the chuck for more leverage. With the jaws in the reversed position, work up to 2-1/4″ (56 mm) can be gripped. This assure maximum accuracy. . The hole through the chuck is. 1″ diameterthis chuck is identical to our p/n 1040 self-centering chuck except that it has a 1″-8 tpi thread that accommodates most wood-working lathes. Jaw tightness on scrolling chucks. As chucks wear, they become looser and easier to turn. Sherline 1043, 3-jaw self-centering wood lathe chuck 3. Rotating the knurled ring closes all three jaws simultaneously to quickly grip round or hexagonal stock.